|
Brand
|
B&R
|
|
Model Number
|
8V1022.00 - 2
|
|
Product Type
|
Servo Drive (ACOPOS)
|
|
Application Areas
|
Wood industry, textile industry, metalworking industry, and general industrial automation
|
|
Mains Input Voltage
|
3x 400 - 480 VAC ± 10%
3x 230 VAC ± 10%
|
|
Frequency
|
50 / 60 Hz ± 4%
|
|
Installed Load Max.
|
3 kVA
|
|
Inrush Current at 400 VAC
|
4 A
|
|
Switch - on Interval
|
> 10 s
|
|
Integrated Line Filter
|
Yes (per EN 61800 - 3, category C3)
|
|
Power Dissipation at Device Nominal Power without Braking Resistor
|
Approx. 120 W
|
|
DC Bus Capacitance
|
235 μF
|
|
24 VDC Power Supply Input Voltage
|
24 VDC ± 25%
|
|
24 VDC Power Supply Input Capacitance
|
8200 μF
|
|
24 VDC Power Supply Current Consumption
|
Max. 2.5 A + current for motor holding brake
|
|
Motor Connection Quantity
|
1
|
|
Continuous Current
|
2.2 A eff
|
|
Peak Current
|
14 A eff
|
|
Nominal Switching Frequency
|
20 kHz
|
|
Possible Switching Frequencies
|
5 / 10 / 20 kHz
|
|
Max. Motor Line Length
|
25 m
|
|
Protective Measures
|
Overload protection, short - circuit and ground fault protection
|
|
Max. Output Frequency
|
598 Hz
|
|
Terminal Connection Cross Section (Flexible and Fine - Stranded Wires with Wire End Sleeve)
|
0.25 to 4 mm²
|
|
Approbation Data (UL / c - UL - us)
|
30 to 10 awg
|
|
Approbation Data (CSA)
|
28 to 10 awg
|
|
Motor Holding Brake Connection Response Threshold for Open - Circuit Monitoring
|
Approx. 385 mA
|
|
Motor Holding Brake Connection Max. Output Current
|
1 A
|
|
Motor Holding Brake Connection Max. Number of Switching Cycles
|
Unlimited (implemented electronically)
|
|
Braking Resistor Peak Power Output
|
3.5 kW
|
|
Braking Resistor Continuous Power
|
130 W
|
|
Limit Switch and Reference Inputs Quantity
|
3
|
|
Limit Switch and Reference Inputs Circuit
|
Sink
|
|
Limit Switch and Reference Inputs Electrical Isolation (Input - ACOPOS)
|
Yes
|
|
Limit Switch and Reference Inputs Electrical Isolation (Input - Input)
|
No
|
|
Limit Switch and Reference Inputs Nominal Voltage
|
24 VDC
|
|
Limit Switch and Reference Inputs Maximum Voltage
|
30 VDC
|
|
Limit Switch and Reference Inputs Switching Threshold (Low)
|
< 5 V
|
|
Limit Switch and Reference Inputs Switching Threshold (High)
|
> 15 V
|
|
Limit Switch and Reference Inputs Current at Nominal Voltage
|
Approx. 4 mA
|
|
Limit Switch and Reference Inputs Switching Delay Max.
|
2.0 ms
|
|
Limit Switch and Reference Inputs Modulation Compared to Ground Potential Max.
|
± 38 V
|
|
Enable Inputs Quantity
|
1
|
|
Enable Inputs Circuit
|
Sink
|
|
Enable Inputs Electrical Isolation (Input - ACOPOS)
|
Yes
|
|
Enable Inputs Nominal Voltage
|
24 VDC
|
|
Enable Inputs Maximum Voltage
|
30 VDC
|
|
Enable Inputs Input Current at Nominal Voltage
|
Approx. 30 mA
|
|
Enable Inputs Switching Threshold (Low)
|
< 5 V
|
|
Enable Inputs Switching Threshold (High)
|
> 15 V
|
|
Enable Inputs Switching Delay (Enable 0 → 1, ready for PWM)
|
Max. 100 μs
|
|
Enable Inputs Switching Delay (Enable 1 → 0, PWM off)
|
Max. 2.0 ms
|
|
Enable Inputs Modulation Compared to Ground Potential Max.
|
± 38 V
|
|
OSSD Signal Connections
|
Not Permitted
|
|
Trigger Inputs Quantity
|
2
|
|
Trigger Inputs Circuit
|
Sink
|
|
Trigger Inputs Electrical Isolation (Input - ACOPOS)
|
Yes
|
|
Trigger Inputs Electrical Isolation (Input - Input)
|
No
|
|
Trigger Inputs Nominal Voltage
|
24 VDC
|
|
Trigger Inputs Maximum Voltage
|
30 VDC
|
|
Trigger Inputs Switching Threshold (Low)
|
< 5 V
|
|
Trigger Inputs Switching Threshold (High)
|
> 15 V
|
|
Trigger Inputs Current at Nominal Voltage
|
Approx. 10 mA
|
|
Trigger Inputs Switching Delay (Rising Edge)
|
52 μs ± 0.5 μs (digitally filtered)
|
|
Trigger Inputs Switching Delay (Falling Edge)
|
53 μs ± 0.5 μs (digitally filtered)
|
|
Trigger Inputs Modulation Compared to Ground Potential Max.
|
± 38 V
|
|
Electrical Discharge Capacitance
|
660 nF
|
|
Energy Efficiency (ie Classification)
|
ie2 (10, 25): 3.8%
ie2 (50, 25): 3.8%
ie2 (10, 50): 4%
ie2 (50, 50): 4%
ie2 (90, 50): 4.1%
ie2 (10, 100): 4.3%
ie2 (50, 100): 4.4%
ie2 (90, 100): 4.7%
Nominal losses in standby mode: 13.2 W
|
|
Permissible Mounting Orientations
|
Hanging vertically: Yes
Horizontal, face up: Yes
Standing horizontally: No
|
|
Installation Elevation above Sea Level (Nominal)
|
0 to 500 m
|
|
Installation Elevation above Sea Level (Maximum)
|
2000 m
|
|
Pollution Degree per EN 61800 - 5 - 1
|
2 (non - conductive pollution)
|
|
Overvoltage Category per EN 61800 - 5 - 1
|
II
|
|
Degree of Protection per EN 60529
|
IP20
|
|
Ambient Temperature (Operation - Nominal)
|
5 to 40 °C
|
|
Ambient Temperature (Operation - Maximum)
|
55 °C
|
|
Ambient Temperature (Storage)
|
- 25 to 55 °C
|
|
Ambient Temperature (Transport)
|
- 25 to 70 °C
|
|
Relative Humidity (Operation)
|
5 to 85%
|
|
Relative Humidity (Storage)
|
5 to 95%
|
|
Relative Humidity (Transport)
|
Max. 95% at 40 °C
|
|
Dimensions (Width)
|
70.5 mm
|
|
Dimensions (Height)
|
375 mm
|
|
Dimensions (Depth)
|
235.5 mm
|
|
Weight
|
4.0 kg
|
|
Certifications
|
CE, UKCA, Functional safety, UL cULus e225616, Power conversion equipment (KC)
|
|
Slots for Plug - in Modules
|
4
|
|
Included in Delivery
|
Shielding component sets (8 x 0010.00 - 1 ACOPOS shielding components set for 8V1022.xxx - x up to 8V1090.xxx - x), Terminal sets (8 x 0001.00 - 1 ACOPOS accessories, connector set for 8V1010.00 to 8V1090.00 (3 - phase))
|
|
Optional Accessories
|
Plug - in modules such as 8AC110.60 - 3 ACOPOS plug - in module (CAN interface), 8AC114.60 - 2 ACOPOS plug - in module (Powerlink v2 interface), etc.
|
